Journal of Samara State Technical University, Ser. Physical and Mathematical SciencesJournal of Samara State Technical University, Ser. Physical and Mathematical Sciences1991-86152310-7081Samara State Technical University4197910.14498/vsgtu1737Research ArticleElastic-plastic analysis of rotating solid shaft by maximumreduced stress yield criterionProkudinAleksandr NikolaevichCandidate of technical sciences, Head Scientist Researchersunbeam_85@mail.ruInstitute of Metallurgy and Mechanical Engineering Far-Eastern Branch of RAS15032020241749404082020Copyright © 2020, Samara State Technical University2020An elasto-plastic rotating solid cylinder under plane strain condition is investigated. The analysis is based on infinitesimal strain theory, maximum reduced stress yield criterion, its associated flow rule and perfectly plastic material behavior. It is assumed that angular velocity is monotonically increasing from 0 to the maximum value and then is monotonically reducing down to 0. In this investigation both loading and unloading phases are considered. It is assumed that angular velocity varies slowly with time, so angular acceleration can be neglected. Under above mentioned assumptions, there is only one non-trivial equilibrium equation in a cylinder. It is established that with increasing angular velocity four plastic regions appear in a cylinder. The last one forms at angular velocity which exceeds fully-plastic limit. Stresses image points of plastic regions lie on different sides and corners of yield surface. As the angular speed decreases, the whole cylinder behaves elastically again. At particular value of angular velocity secondary plastic flow may starts at the center of cylinder. Replasticization is possible only for sufficiently high maximum angular speed and the entire cylinder may be replasticized. Four secondary plastic regions may appear in the cylinder under unloading. The stresses image points in primary and secondary regions lie on opposite sides and corners of yield surface. In the present analysis it is assumed that the entire cylinder becomes replasticized just at stand-still. In this case only two secondary plastic regions emerge. Exact solutions for all stages of deformation are obtained. The systems of algebraic equations for determination of integration constants and border radii are formulated. The obtained results are illustrated by the distributions of stresses and plastic strains in the cylinder rotating at different speeds. Presented solutions are compared with known analytical solutions based on Tresca's criterion.elastic-plastic strainsexact solutionrotating shaftmaximum reduced stress yield criterionупругопластические деформацииточное решениевращающийся цилиндрусловие максимальных приведенных напряжений[Sadd M. H., Elasticity: Theory, Applications, and Numerics, Elsevier, Academic Press, Amsterdam, New York, 2014][Timoshenko S., Theory of Elasticity, McGraw Hill, New York, 2010][Nadai A., Theory of Flow and Fracture of Solids, v. 1, McGraw Hill, New York, 1950][Hodge P. G., Balaban M., "Elastic—plastic analysis of a rotating cylinder", Int J. Mech. Sci., 4:6 (1962), 465-476][Gamer U., "On the applicability of Tresca's yield condition to the rotating solid shaft", Rev. Roum. Sci. Techn.-Mec. Appl., 29:1 (1984), 27-30][Gamer U., Sayir M., "Elastic-plastic stress distribution in a rotating solid shaft", Z. angew. Math. Phys., 35:5 (1984), 601-617][Gamer U., Mack M., Varga I., "Rotating elastic-plastic solid shaft with fixed ends", Int. J. Eng. Sci., 35:3 (1997), 253-267][Lindner T., Mack W., "Residual stresses in an elastic-plastic solid shaft with fixed ends after previous rotation", Z. angew. Math. Mech., 78:2 (1998), 75-86][Mack W., "The rotating elastic-plastic solid shaft with free ends", Tech. Mech., 12:2 (1991), 119-124][Gamer U., Lance R. H., "Stress distribution in a rotating elastic-plastic tube", Acta Mechanica, 50 (1983), 1-8][Mack W., "Rotating elastic-plastic tube with free ends", Int. J. Solids Str., 27:11 (1991), 1461-1476][Eraslan A. N., "On the linearly hardening rotating solid shaft", Eur. J. Mech.-A/Solids, 22:2 (2003), 295-307][Eraslan A. N., "Von Mises' yield criterion and nonlinearly hardening rotating shafts", Acta Mechanica, 168 (2004), 129-144][Eraslan A. N. and T. Akis, "On the plane strain and plane stress solutions of functionally graded rotating solid shaft and solid disk problems", Acta Mechanica, 181 (2006), 43-63][Akis T., Eraslan A. N., "Exact solution of rotating FGM shaft problem in the elastoplastic state of stress", Arch. Appl. Mech., 77 (2007), 745-765][Argeso H., Eraslan A. N., "A computational study on functionally graded rotating solid shafts", Int. J. Comput. Methods Eng. Sci. Mech., 8:6 (2007), 391-399][Eraslan A. N., Arslan E., "Plane strain analytical solutions to rotating partially plastic graded hollow shafts", Turkish J. Eng. Env. Sci., 31:5 (2007), 273-287][Nejad M.Z., Fatehi P., "Exact elasto-plastic analysis of rotating thick-walled cylindrical pressure vessels made of functionally graded materials", Int. J. Eng. Sci., 86 (2015), 26-43][Schmidt R., "Über den Zusammenhang von Spannungen und Formänderungen im Verfestigungsgebiet", Ing. Arch., 3 (1932), 215-235][Ишлинский А. Ю., "Гипотеза прочности формоизменения", Ученые записки МГУ. Механика, 1940, № 46, 117-124][Hill R., "On the inhomogeneous deformation of a plastic lamina in a compression test", Phil. Mag, Ser. 7, 41:319 (1950), 733-744][Ivlev D. D., "On the development of a theory of ideal plasticity", J. Appl. Math. Mech., 22:6 (1958), 1221-1230][Ишлинский А. Ю., Ивлев Д. Д., Математическая теория пластичности, Физматлит, М., 2003, 704 с.][Буренин А. А., Ткачева А. В., Щербатюк Г. А., "К расчету неустановившихся температурных напряжений в упругопластических телах", Вычислительная механика сплошных сред, 10:3 (2017), 245-259][Буренин А. А., Ткачева А. В., Щербатюк Г. А., "К использованию кусочно-линейных пластических потенциалов в нестационарной теории температурных напряжений", Вестн. Сам. гос. техн. ун-та. Сер. Физ.-мат. науки, 22:1 (2018), 23-39][Буренин А. А., Каинг М., Ткачева А. В., "К расчету плоских напряженных состояний в теории неустановившихся температурных напряжений в упругопластических телах", Дальневост. матем. журн., 18:2 (2018), 131-146][Cai Q., Pang M., Zhang Y.-Q., Liu X., "Elastic-plastic stress distribution of rotating annular disc based on twin-shear stress yield criterion", J. Zhejiang Univ., Eng. Sci., 42:9 (2008), 1540-1544][Zhao D.-W., Xie Y.-J., Liu X.-H., Wang G.-D., "Three-dimensional analysis of rolling by twin shear stress yield criterion", J. Iron Steel Res. Int., 13 (2006), 21-26][Zhu X., Pang M., Zhang Y., "Estimation of burst pressure of pipeline using twin-shear stress yield criterion", Chinese J. Appl. Mech., 28:2 (2011), 135-138]