Urban construction and architectureUrban construction and architecture2542-01512782-2109Eco-vector5508710.17673/Vestnik.2020.03.21Research ArticleINFLUENCE OF CHANNEL GEOMETRY, PRESSURE, TEMPERATURE, OSCILLATIONS AND ADSORPTION ON OBLITERATION OF SLIT SEALS OF ELECTRIC POWER SYSTEMSKRESTINEvgeny A.vestniksgasu@yandex.ruSEREBRYAKOVGrigoriy V.vestniksgasu@yandex.ruSamara State Technical University1512202010317017614122020Copyright © 2020, KRESTIN E.A., SEREBRYAKOV G.V.2020The infl uence of the geometric dimensions and confi guration of slot contactless seals on the obliteration of the gaps of plunger pairs at the design and calculation stage of drive systems of electric power systems units is considered. The combined eff ect of working fl uid contamination and the adsorption eff ect on the overgrowth of the living section of the channel was revealed. The fl ow rate during sample shedding was reduced simultaneously as a result of the channel overgrowing with contamination particles and adsorption, i.e. the formation of boundary fi lms on the channel walls. Leaks through the gap at concentric and eccentric position of the plunger in the sleeve are determined. The minimum gap is found, at which the obliteration process is stabilized and loose mud formations are washed away by the fl ow of the working fl uid. The infl uence of the pressure drop at the ends of the slot gap on the channel obliteration process was revealed. With an increase in the pressure drop, the process of stratifi cation of adsorbed layers of polar molecules accelerates, resulting in an increase in the number of contamination particles trapped in the gap per unit of time. With an increase in the temperature of the working fl uid, the process of channel obliteration accelerates, which is confi rmed by experiments. With an oscillating plunger, the fl ow through the annular gap is less than with a stationary one. This is due to the fact that the oscillating plunger occupies a position in the sleeve close to the concentric one, at which leaks are minimal. A stable fl ow rate is obtained when the working fl uid fl ows through the gaps of the plunger pairs performing reciprocating oscillating movements.obliterationslot gapsleakage ratehydraulic unitsboundary layer thicknessadsorptioneccentric arrangementelectric power systemsоблитерациящелевые зазорырасход утечекгидроагрегатыэлектроэнергетические системыплунжерные парызагрязнения[Никитин Г.А., Черкун В.Е., Дидур В.А. Повышение качества сборки плунжерных пар золотниковых распределителей // Технология и организация производства. Киев, 1971. № 1. С. 77-80.][Крестин Е.А. Определение утечек жидкости через зазор бесконтактного уплотнения поршня гидравлического вибратора // Научное обозрение. 2014. №5. С. 108-110.][Васильев В.А. Метод расчета гидродинамических сил в щелевых уплотнениях роторов мощных питательных насосов // Вестн. ЮУрГУ. Сер. Машиностр. 2004. № 5. С. 115-120.][Гидравлика, гидромашины и гидроприводы / Т.М. Башта и др. 5-е изд., стер. М.: Альянс, 2011. 422 с.][Численное исследование устойчивости течения Тейлора между двумя цилиндрами в двумерном случае / О. М. Белоцерковский [и др.] // Журнал вычислительной математики и математической физики. 2009. № 4. С. 754-768.][Уплотнительные устройства в машиностроении / Б. Жирных [и др.]. М.: Издательство МГТУ им. Баумана, 2017. 24 с.][Никитин О.Ф. Рабочие жидкости и уплотнительные устройства гидроприводов. М.: МГТУ им. Н. Э. Баумана, 2013. 288 с.][Maшиностроительный гидропривод / под ред. В. Н. Прокофьева; авт.: Л. А. Кондаков, Г. А. Никитин, В. Н. Прокофьев, В. Я. Скрицкий, В. Л. Сосонкин. М.: Машиностроение, 1978. 495 с.][Найгерт К.В., Редников С.Н., Япарова Н.М. Процессы полимеризации рабочей среды в зазорах золотниковых пар // Вестник ПНИПУ. Аэрокосмическая техника: сборник статей. Челябинск, 2016. № 46. С. 125-123.]