Evaluation of the Durability of Dry Mix Compositions Based on Gypsum and Gypsum Cement for 3D Printing


Дәйексөз келтіру

Толық мәтін

Ашық рұқсат Ашық рұқсат
Рұқсат жабық Рұқсат берілді
Рұқсат жабық Тек жазылушылар үшін

Аннотация

The effectiveness of using 3D printing technology for the construction of exterior and interior walls, especially for low-rise residential and civil buildings of social purpose, is substantiated. The domestic experience in the construction of single-storey frameless buildings with load-bearing external walls printed on a 3D printer (with filling their internal space with inorganic insulation materials on a monolithic (foam concrete, foam gypsum) or backfill (expanded perlite, especially light expanded clay gravel) basis) is analyzed. The use of dry mixes on a gypsum and mixed basis for printing walls of low-rise buildings is justified for technological and economic reasons. On the basis of laboratory and field experiments to assess the durability of gypsum cement-pozzolan compositions (from dry mixtures) for 3D printing to change the temperature and humidity regime, it was established that the reason for the destruction and demolition of prototypes according to quantitative X-ray phase analysis was an increased content of ettringite during their hydration and hardening at a reduced temperature.

Толық мәтін

Рұқсат жабық

Авторлар туралы

R. Shigapov

Ufa State Petroleum Technical University

Хат алмасуға жауапты Автор.
Email: ufagips@mail.ru

Associate Professor

Ресей, Ufa

G. Shagigalin

Ufa State Petroleum Technical University

Email: ufa-gazinur@mail.ru

Assistant

Ресей, Ufa

A. Klyuev

Belgorod State Technological University named after. V.G. Shukhov

Email: ufagips@mail.ru

Candidate of Sciences (Engineering), Associate Professor

Ресей, Belgorod

B. Bulatov

Bashkir State Agrarian University

Email: bfd82@mail.ru

Senior Lecturer

Ресей, Ufa

D. Metlitskaya

Ufa State Petroleum Technical University

Email: darya.metlickaya333@mail.ru

Student of Group MPG05-23-01

Ресей, Ufa

I. Nedoseko

Ufa State Petroleum Technical University

Email: nedoseko1964@mail.ru

Doctor of Sciences (Engineering), Professor

Ресей, Ufa

Әдебиет тізімі

  1. Akulova I.I., Slavcheva G.S., Makarova T.V. Technical and economic estimate of efficiency of using 3D printing in housing construction. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2019. No. 12, pp. 52–56. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2019-12-52-56
  2. Slavcheva G.S. 3D-build printing today: potential, challenges and prospects for implementation. Stroitel’nye Materialy [Construction Materials]. 2021. No. 5, pp. 28–36. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2021-791-5-28-36
  3. Kumar L.J., Krishnadas Nair C.G. Current Trends of Additive Manufacturing in the Aerospace Industry. In: Advances in 3D Printing & Additive Manufacturing Technologies. Springer, Singapore. 2017 https://doi.org/10.1007/978-981-10-0812-2_4
  4. Slavcheva G.S., Akulova I.I., Vernigora I.V. Concept and effectiveness of 3D printing for urban environment design. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2020. No. 3, pp. 49–55. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2020-3-49-55
  5. Klyuev S.V., Klyuev A.V., Vatin N.I., Shorstova E.S. Technology of 3-D printing of fiber reinforced mixtures. In: Sustainable Energy Systems: Innovative Perspectives. SES 2020. Lecture Notes in Civil Engineering. 2021. Vol. 141. https://doi.org/10.1007/978-3-030-67654-4_25
  6. Ryazanov A.N., Shigapov R.I., Sinitsin D.A., Kinzyabulatova D.F., Nedoseko I.V. The use of gypsum compositions in the technologies of construction 3D printing of low-rise residential buildings. Problems and prospects. Stroitel’nye Materialy [Construction Materials]. 2021. No. 8, pp. 39–44. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2021-794-8-39-44
  7. Slavchev G.S., Makarova T.V. Foam concretes for heat insulation layers of external walls constructed by the method of 3D printing. Stroitel’nye Materialy [Construction Materials]. 2018. No. 10, pp. 30–35. DOI: https://doi.org/10.31659/0585-430X-2018-764-10-30-35 (In Russian).
  8. Le T.T., Austin S.A., Lim S., Buswell R.A., Gibb A.G.F., Thorpe T. Mix design and fresh properties for high-performance printing concrete. Materials & Structures. 2012. Vol. 45, pp. 1221–1232. https://doi.org/10.1617/s11527-012-9828-z
  9. Bulatov B.G., Nedoseko I.V. Prospects for using the results of the automation system for the production of wall products from phosphogypsum. Izvestiya of the Kazan State University of Architecture and Civil Engineering. 2017. No. 1 (39), pp. 302–308. (In Russian).
  10. Bulatov B.G., Nedoseko I.V. Control system for the processing of multi-tonnage gypsum-containing waste from the production of mineral fertilizers – phosphogypsum – into finished products. Vestnik of the Bashkir State Agrarian University. 2015. No. 2 (34), pp. 69–73. (In Russian).
  11. Glagolev E.S., Lesovik V.S., Bychkova A.A. 3D printing of buildings and building components as the future of sustainable construction. In the collection: Nature-like technologies of building composites for protecting the human environment. II International online congress dedicated to the 30th anniversary of the Department of Building Materials Science, Products and Structures. Belgorod. 2019, pp. 303–309. (In Russian).
  12. Alekseeva N.S. Prospects for the use of 3D printing in construction. In the collection: Economics and management: trends and prospects: Materials of the I Interuniversity scientific and practical conference of the Faculty of Economics and Management. Saint Petersburg. 2020, pp. 211–216. (In Russian).
  13. Klyuev S.V., Klyuev A.V., Kuzik E.S. Additive technologies in the construction industry. Intelligent building composites for green construction: International scientific and practical conference dedicated to the 70th anniversary of the Honored Scientist of the Russian Federation, corresponding member of the RAASN, Doctor of Technical Sciences, Professor Valery Stanislavovich Lesovik. Belgorod, March 15–16, 2016, pp. 54–58. (In Russian). EDN WIJFAF.
  14. Slavcheva G.S., Shvedova M.A., Babenko D.S. Analysis and criteria assessment of rheological behavior of mixes for construction 3-D printing. Stroitel’nye Materialy [Construction Materials]. 2018. No. 12, pp. 34–40. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2018-766-12-34-40.
  15. Mukhametrakhimov R.Kh., Ziganshina L.V. Technology and quality control of construction 3D printing. Izvestiya of the Kazan State University of Architecture and Civil Engineering. 2022. No. 1 (59), pp. 64–79. https://doi.org/10.52409/20731523_2022_1_64 EDN BZJGUO.
  16. Mukhametrakhimov R., Ziganshina L., Kadyrov R., Statsenko E. Structure of 3D-printed concrete by x-ray computed tomography. In: Proceedings of STCCE 2022. STCCE 2022. Lecture Notes in Civil Engineering. 2023. Vol. 291. https://doi.org/10.1007/978-3-031-14623-7_37
  17. Pustovgar A.P., Adamtsevich L.A., Adamtsevich A.O. International research experience in the field of additive construction manufacturing. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2023. No. 11, pp. 4–10. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2023-11-4-10
  18. Bessonov I.V., Shigapov R.I., Babkov V.V. Thermal insulating foam gypsum in low-rise construction. Stroitel’nye Materialy [Construction Materials]. 2014. No. 7, pp. 9–13. (In Russian).
  19. Mirsaev R.N., Babkov V.V., Nedoseko I.V., Yunusova S.S. at al. Experience in the production and operation of gypsum wall products. Stroitel’nye Materialy [Construction Materials]. 2008. No. 3, pp. 78–80. (In Russian).
  20. Larionova Z.M., Nikitina L.V., Garashin V.R. Fazovyy sostav, mikrostuktura i prochnost’ tsementnogo kamnya i betona [Phase composition, microstructure and strength of cement stone and concrete]. Moscow: Stroyizdat. 1977. 254 p.
  21. Alksnis F.F. Tverdeniye i destruktsiya gipsotsementnykh kompozitsionnykh materialov [Hardening and destruction of gypsum-cement composite materials]. Leningrad: Stroyizdat. 1988. 103 p.
  22. Mukhametrakhimov R.Kh. Study of plasticizing additives based on polycarboxylate esters on the properties of concrete molded by 3D printing. Stroitel’nyye materialy i izdeliya. 2022. Vol. 5. No. 5, pp. 42–58. https://doi.org/10.58224/2618-7183-2022-5-5-42-58 EDN CLDKGL.

Қосымша файлдар

Қосымша файлдар
Әрекет
1. JATS XML
Жүктеу
2. Fig. 1. Four-apartment one-story residential buildings for social purposes

Жүктеу (183KB)
Метадеректер
3. Fig. 2. Innovative digital medical and midwifery station built using 3D printing

Жүктеу (260KB)
Метадеректер
4. Fig. 3. «Quadrum» cottage village, Aisha villaage in the suburbs of Kazan

Жүктеу (239KB)
Метадеректер
5. Fig. 4. Fragment of a 3D-printed wall filled with foam concrete

Жүктеу (137KB)
Метадеректер
6. Fig. 5. Construction of a single-pitched roof with a wooden rafter system, «Quadrum» cottage village, Aisha village

Жүктеу (159KB)
Метадеректер
7. Fig. 6. Dry mixture for construction 3D printing produced by Ufa Gypsum Company LLC

Жүктеу (127KB)
Метадеректер
8. Fig. 7. Plastering station for mixing the dry mixture and supplying the solution to the printer hopper

Жүктеу (213KB)
Метадеректер
9. Fig. 8. Small architectural forms displayed in an open area for the autumn-winter period of operation for the climatic conditions of central Russia

Жүктеу (196KB)
Метадеректер
10. Fig. 9. X-ray phase analysis of samples made from dry building mixture based on HCPB

Жүктеу (141KB)
Метадеректер

© ООО РИФ "СТРОЙМАТЕРИАЛЫ", 2024

Осы сайт cookie-файлдарды пайдаланады

Біздің сайтты пайдалануды жалғастыра отырып, сіз сайттың дұрыс жұмыс істеуін қамтамасыз ететін cookie файлдарын өңдеуге келісім бересіз.< / br>< / br>cookie файлдары туралы< / a>