Improving the Drive of the Rolling Mill 2000 at PJSC Severstal
- Authors: Gerasimova A.A.1, Vasiliev M.V.1, Nagovitsyn V.A.1
-
Affiliations:
- National Research and Engineering University "MISIS"
- Issue: Vol 9, No 1 (2022)
- Pages: 154-160
- Section: Articles
- URL: https://journals.eco-vector.com/2313-223X/article/view/529885
- DOI: https://doi.org/10.33693/2313-223X-2022-9-1-154-160
- ID: 529885
Cite item
Open Access
Access granted
Abstract
The purpose of the scientific work is to modernize the gear cage of the hot rolling mill 2000 at PJSC Severstal, which will increase the service life of the drive as a whole. The method of drive modernization consists in the modernization of the gear cage, namely, the replacement of the chevron engagement with an increased class of manufacturing accuracy and contact strength of gears, with the same dimensions of the foundations. As a result of the calculations performed, it was found: an increase in service life due to the material, the average service life of the chevron engagement made of steel grade 12KHN3A is 8.2 years, the possibility of reducing the width of the gear engagement. When calculating the contact strength, the calculated value was 872.9 MPa, which did not exceed the permissible 1209.6 MPa. The bending load capacity also showed an estimated value of 116.8 MPa, not exceeding the permissible 458.1 MPa. The designed gear engagement, where the module, the number of teeth and the width of the gear ring were changed, has fatigue endurance.
Keywords
Full Text
About the authors
Alla A. Gerasimova
National Research and Engineering University "MISIS"
Email: allochka@rambler.ru
Cand. Sci. (Eng.); associated professor Moscow, Russian Federation
Mikhail V. Vasiliev
National Research and Engineering University "MISIS"
Email: mv@karfidovlab.com
senior lecturer Moscow, Russian Federation
Vladimir A. Nagovitsyn
National Research and Engineering University "MISIS"
Email: nagovitsin.91@mail.ru
graduate student Moscow, Russian Federation
References
- Tselikov A.I., Polukhin P.I., Grebenik V.M. et al. Machines and aggregates for the production and finishing of rolled products: Textbook for universities. Moscow: Metallurgiya, 1987.
- Trends in the production and economic indicators of metallurgical and pipe enterprises in Russia [Electronic resource]. URL: https://www.elibrary.ru/item.asp?id=24153477 (data of accesses: 16.11.2021).
- The official website of PJSC Severstal [Electronic resource]. URL: https://chermk.severstal.com/ (data of accesses: 16.10.2021).
- Gerasimova A.A., Radyuk A.G., Zarapin A.Yu. The calculation of the thickness of thermal spray coating for protection of low alloyed steel when heated under rolling // Materials Science Forum. 2018. Vol. 945. Pp. 729-734. doi: 10.4028/
- Rudskoy A.I., Lunev V.A. Theory and technologies of rolling production. Moscow: Lan Publishing House, 2016. 528 p.
- Gerasimova A.A. Investigation of the regularities of plastic deformation of hollow steel profiles by compression. Computational Nanotechnology. 2019. No. 3. Pp. 22-26. (In Rus.)
- Dykha A., Artiukh V., Sorokatyi R. et al. Modeling of wear processes in a cylindrical plain bearing // Advances in Intelligent Systems and Computing. 2021. 1259 AISC. Pp. 542-552.
- Fomin A.A., Gusev V.G., Timerbaev N.F. The processing of the profile surface of the work-pieces, characterized by low rigidity // Solid State Phenomena. 2020. 299 SSP. Pp. 852-860.
- Verenev V.V., Bolshakov V.I. State of vibration diagnostics and monitoring of rolling mill equipment. Fundamental and applied problems of ferrous metallurgy. 2006. No. 12. Pp. 267-281.
- Gorbatyuk S.M. Technologies and machines of pressure treatment: Textbook. Moscow: Publishing House of NUST MISIS, 2019.
- Liu J., Zhu C., Li G. application research progress of coatings on copper plate in continuous casting mould. Cailiao Daobao/Materials Reports. 2019. No. 33 (9). Pp. 2831-2838.
- Devyatiarova V.V., Balakhnina E.E., Valeeva L.M. Development of a mathematical model for a workpiece heating and cooling in a protective medium while treatment under pressure // Defect and Diffusion Forum. 2021. No. 410. Pp. 115-122. doi: https://doi.org/10.4028/www.scientific.net/ddf.410.115.
- Gerasimova A.A., Valeeva L.M. Development of a technological scheme for rolling 10G2SFB thick sheet steel // Journal of Advanced Research in Technical Science. 2020. Issue 19. Pp. 17-21. doi: 10.26160/2474-5901-2020-19-17-21.
- State Standard GOST 1643-81 Basic standards of interchangeability. Gear gears are cylindrical. Moscow: Publishing House of Standards, 1981.
- Chernavsky S.A., Snesarev G.A., Kosinzov B.S. Mechanical transmission design. Moscow: Mechanical Engineering, 1984.
Supplementary files
