Structure and Properties of Fine-Grained Concrete Based on Gypsum-Cement-Pozzolan Dry Mortars for 3DCP


Дәйексөз келтіру

Толық мәтін

Ашық рұқсат Ашық рұқсат
Рұқсат жабық Рұқсат берілді
Рұқсат жабық Тек жазылушылар үшін

Аннотация

3D concrete printing (3DCP) is one of the most important priorities for the development of the construction industry around the world. Despite optimistic forecasts for the growth of additive construction technology in the long term, there are various risks that can influence the pace of this development, which are associated, first of all, with the need to develop the regulatory framework, train qualified personnel, create and improve equipment and materials for 3DCP – seal. There is a lot of research aimed at creating and developing the scientific basis for the design of concrete for construction 3D printing; compositions of dry mortars for additive manufacturing based on mineral binders, mainly cement, have been proposed; much less attention is paid to composites based on gypsum and mixed – gypsum-cement-pozzolan binders (GCPB). The purpose of this work is to study the structure and properties of fine-grained concrete for 3DCP based on gypsum-cement-pozzolan dry mortars. The molding of samples during experimental studies was carried out using the layer-by-layer extrusion method on a workshop construction 3D printer “AMT S-6044”. The rationality of using concrete with a ratio of GCPB:aggregate = 1:2 in the additive manufacturing technology with a sand fineness modulus of Mk 3 has been substantiated. A composition of gypsum-cement-pozzolanic concrete (GCPC) modified with a multifunctional complex additive has been developed, which allows increasing the compressive strength by 35.3%, water resistance – by 73% (up to 0.85) compared to the control unmodified composition. It has been established that modification of GCPB with the developed multifunctional complex additive leads to a decrease in the volume of open capillary pores by 20.5%, the volume of open non-capillary pores – by 66.7%, an increase in the volume of conditionally closed pores by 28.1%, and the microporosity index – from 0.22 to 0.89. The synergistic interaction of chemical additives in complex additive composition is confirmed by the results of studies performed to determine the electrokinetic potential on the surface of GCPB particles and the kinetics of heat release during its hydration.

Толық мәтін

Рұқсат жабық

Авторлар туралы

R. Rakhimov

Kazan State University of Architecture and Engineering

Хат алмасуға жауапты Автор.
Email: rahimov@kgasu.ru

Doctor of Sciences (Engineering)

Ресей, Kazan

R. Mukhametrakhimov

Kazan State University of Architecture and Engineering

Email: muhametrahimov@mail.ru

Candidate of Sciences (Engineering)

Ресей, Kazan

A. Galautdinov

Kazan State University of Architecture and Engineering

Email: galautdinov89@mail.ru

Candidate of Sciences (Engineering)

Ресей, Kazan

L. Ziganshina

Kazan State University of Architecture and Engineering

Email: lilya0503199@gmail.com

Candidate of Sciences (Engineering)

Ресей, Kazan

Әдебиет тізімі

  1. Wang L., Ma G., Liu T., Buswell R., Li Z. Interlayer reinforcement of 3D printed concrete by the in-process deposition of U-nails. Cement and Concrete Research. 2021. Vol. 148. 106535. https://doi.org/10.1016/j.cemconres.2021.106535
  2. Bai G., Wang L., Wang F., Ma G. In-process reinforcing method: dual 3D printing procedure for ultra-high-performance concrete reinforced cementitious composites. Materials Letters. 2021. Vol. 304. 130594. https://doi.org/10.1016/j.matlet.2021.130594
  3. Ma G., Buswell R., Leal da Silva, W. R., Wang L., Xu J., Jones S. Z. Technology readiness: A global snapshot of 3D concrete printing and the frontiers for development. Cement and Concrete Research. 2022. Vol. 156. 106774. https://doi.org/10.1016/j.cemconres.2022.106774
  4. Poluektova V.A. Designing the composition of a cement-based 3d construction printing material. Inorganic Materials: Applied Research. 2020. Vol. 11. No. 5, pp. 1013–1019. https://doi.org/10.1134/S2075113320050263
  5. Demyanenko O., Sorokina E., Kopanitsa N., Sarkisov Y. Mortars for 3D printing. MATEC Web of Conferences. 2018. Vol. 143. 02013. https://doi.org/10.1051/matecconf/201714302013
  6. Molodin V.V., Vasenkov E.V., Timin P.L. Work head for 3d printing of insulated walls from one-stage polystyrene concrete. Materials Science Forum. 2020. Vol. 992, pp. 194–199. https://doi.org/10.4028/www.scientific.net/MSF.992.194
  7. Mukhametrakhimov R.Kh., Lukmanova L.V. The influence of Portland cements with different mineralogical composition on the basic properties of composites formed by layer-by-layer extrusion (3D printing). Izvestiya of the Kazan State University of Architecture and Civil Engineering. 2021. No. 2 (56), pp. 37–50. (In Russian). https://doi.org/10.52409/20731523_2021_2_37
  8. Mukhametrakhimov R., Lukmanova L. Structure and properties of mortar printed on a 3D printer. Magazine of Civil Engineering. 2021. Vol. 102. No. 2. https://doi.org/10.34910/MCE.102.6
  9. Slavcheva G.S. Drying and shrinkage of cement paste for 3D printable concrete. IOP Conference Series: Materials Science and Engineering. Vol. 481. IV International Conference on Safety Problems of Civil Engineering Critical Infrastructures. 4–5 October 2018, Russian Federation. https://doi.org/10.1088/1757-899X/481/1/012043
  10. Korolev E.V., Zyong T.K., Inozemtsev A.S. Method for providing internal hydration care for cement in 3D printing compositions. Vestnik MGSU. 2020. Vol. 15, No. 6, pp. 834–846. (In Russian). https://doi.org/10.22227/1997-0935.2020.6.834-846
  11. Slavcheva G.S., Artamonova O.V. Rheological behavior and mix design for 3D printable cement paste. Key Engineering Materials. 2019. Vol. 799, pp. 282–287. https://doi.org/10.4028/www.scientific.net/KEM.799.282
  12. Mukhametrakhimov R.Kh., Rakhimov R.Z., Galautdinov A.R., Ziganshina L.V. Modified gypsum-cement-pozzolan concrete for 3DCP. Stroitel’nye Materialy [Construction Materials]. 2024. No. 1–2, pp. 79–89. (In Russian). https://doi.org/10.31659/0585-430X-2024-821-1-2-79-89
  13. Rakhimov R.Z., Mukhametrakhimov R.Kh., Galautdinov A.R., Ziganshina L.V. Gypsum-cement-puzzolanic concrete for 3D CP. Vestnik MGSU. 2024. Iss. 19. No. 4, pp. 580–595. (In Russian). https://doi.org/10.22227/1997-0935.2024.4.580-595
  14. Khaliullin M.I., Dimieva A.I., Faizrakhmanov I.I. The influence of additives of mechanically activated mineral fillers on the properties of composite gypsum binders. Izestiya of the Kazan State University of Architecture and Civil Engineering. 2019. No. 4 (50), pp. 386–393. (In Russian).
  15. Altykis M.G., Rakhimov R.Z. Gips. Stroitel’nye materialy i izdeliya [Gypsum. Construction materials and products]. Kazan’: KISI, 1994. 107 p.
  16. Rakhimov R.Z., Khaliullin M.I. Status and development trends of the gypsum building materials industry. Stroitel’nye Materialy [Construction Materials]. 2010. No. 12. pp. 44–46. (In Russian).
  17. Rakhimov R.Z., Rakhimova N.R. Istoriya kompozitsionnykh mineral’nykh vyazhushchikh veshchestv [History of composite mineral binders]. SPb: Lan’. 2023. 268 p.
  18. Rakhimov R.Z., Rakhimova N.R. Istoriya nauki i tekhniki [History of science and technology]. SPb: Lan’. 2022. 528 p.
  19. Lesovik V.S., Elistratkin M.Yu., Glagolev E.S., Shatalova S.V., Starikov M.S. Formation of properties of compositions for construction printing. Vestnik BSTU named after V.G. Shukhov. 2017. Vol. 2. No. 10, pp. 6–14. (In Russian).
  20. Smirnov D.S., Belaeva K.R., Khokhryakov O.V. Study of the properties of fine-grained asphalt concrete designed by different methods. Izestiya of the Kazan State University of Architecture and Civil Engineering. 2023. No. 3 (65), pp. 66–76. (In Russian). doi: 10.52409/20731523_2023_3_66
  21. Belyakov A.Yu., Khokhryakov O.V., Khozin V.G. Functionalized mineral filler is an effective modifier for cement concrete. Izestiya of the Kazan State University of Architecture and Civil Engineering. 2023. No. 3 (65), pp. 45–56. (In Russian). https://doi.org/10.52409/20731523_2023_3_45
  22. Morozova N.N., Gulyakov E.G. Properties of concrete with zeolite-containing binder. Izestiya of the Kazan State University of Architecture and Civil Engineering. 2023. No. 2 (64), pp. 27–39. (In Russian). doi: 10.52409/20731523_2023_2_27
  23. Shorstova E.S. Basalt fiber reinforced concrete for 3D printing based on a composite binder. Cand. Diss. (Engineering). Belgorod. 2022. 176 p. (In Russian).
  24. Slavcheva G.S., Ibryaeva A.I. Influence of concentration and granulometry of fillers on the rheological properties of cement systems. Vestnik of Tver State Technical University. Series: Construction. Electrical Engineering and Chemical Technology. 2019. Vol. 2, No. 2, pp. 29–36. (In Russian).
  25. Britvina E.A., Slavcheva G.S. Manufacturability indicators of cement mixtures for construction 3D printing: modeling and experimental studies. Vestnik Vestnik of the FEFU Engineering School. 2021. Vol. 49. No. 4, pp. 56–65. (In Russian). https://doi.org/10.24866/2227-6858/2021-4/56-65
  26. Torshin A.O., Borovikova S.O., Korchunov I.V., Potapova E.N. Development of a building mixture for 3D printing. Uspekhi v khimii i khimicheskoi tekhnologii. 2018. Vol. 2. No. 198, pp. 164–166. (In Russian).
  27. Potapova E., Guseva T., Shchelchkov K., Fischer H.B. Mortar for 3D printing based on gypsum binders. Materials Science Forum. 2021. Iss. 1037 (5), pp. 26–31. https://doi.org/10.4028/www.scientific.net/MSF.1037.26
  28. Shatalova S.V., Chernysheva N.V., Elistratkin M.Yu., Drebezgova M.Yu., Masalitina S.V. Rheological properties of gypsum cement binders and molding mixtures based on them for 3D additive construction technologies. Stroitel’nye Materialy [Construction Materials]. 2022. No. 8, pp. 23–30. (In Russian). https://doi.org/10.31659/0585-430X-2022-805-8-23-30
  29. Patent RF 2777886. Modifitsirovannaya stroitel’naya smes’ dlya 3D-pechati [Modified mortar for 3D printing]. Mukhametrakhimov R.Kh., Ziganshina L.V. Declared 30.12.2021. Published 11.08.2022. (In Russian).
  30. Zaporozhets I.D., Okorokov S.D., Pariiskii A.A. Teplovydelenie betona [Heat release of concrete]. Moscow: Stroyizdat. 1966. 314 p.
  31. Kaprielov S.S., Batrakov V.G., Sheinfel’d A.V. New generation modified concretes: reality and prospects. Beton i zhelezobeton. 1999. Vol. 6, pp. 6–10. (In Russian).
  32. Abramova A.Yu. Increasing the efficiency of mixtures of dry construction adhesives based on cement binders. Cand. Diss. (Engineering). Moscow. 2023. 195 p. (In Russian).
  33. Shoshin E.A., Ivashchenko Yu.G., Shirokov A.A., Rufimskii P.V. The influence of phase transitions on the electrokinetic potential of the dispersed phase of cement paste. Vestnik of the Saratov State Technical University. 2014. Vol. 1. No. 74, pp. 108–111. (In Russian).

Қосымша файлдар

Қосымша файлдар
Әрекет
1. JATS XML
Жүктеу
2. Fig. 1. Dependences of average density, compressive and bending strengths of fine-grained concrete on the fineness modulus of quartz sand:      – Rcompr;      – Rbend; ----- – average density

Жүктеу (78KB)
Метадеректер
3. Fig. 2. Dependences of average density, compressive and bending strengths of fine-grained concrete of the studied GCPC mixes (mix No. 1–3):      – Rcompr;      – Rbend; ----- – average density

Жүктеу (76KB)
Метадеректер
4. Fig. 3. Kinetics of heat release during hydration of the studied GCPB mixes: 1 – composition # 1; 2 – composition # 2; 3 – composition # 3

Жүктеу (154KB)
Метадеректер
5. Fig. 4. Zeta potential of gypsum-cement-pozzolan suspensions: 1 – control; 2 – with the addition of Best-TB, 0.9%; 3 – with a multifunctional complex additive

Жүктеу (69KB)
Метадеректер

© ООО РИФ "СТРОЙМАТЕРИАЛЫ", 2024

Осы сайт cookie-файлдарды пайдаланады

Біздің сайтты пайдалануды жалғастыра отырып, сіз сайттың дұрыс жұмыс істеуін қамтамасыз ететін cookie файлдарын өңдеуге келісім бересіз.< / br>< / br>cookie файлдары туралы< / a>