Elaboration and testing of the algorithm which ensures an achievement of minimal deviation angle of flying model’s main centroidal axis of inertia during her counterbalancing in a sole correction flatness

封面

如何引用文章

全文:

详细

High complexity and cost of developing flying models necessitate the use of such design and production techniques that would ensure the best flight technical and technological characteristics of the model also would raise of it operation effectiveness. These techniques include the experimental control method of flying model’s mass-inertia asymmetry parameters during final assembly of the model. Solution of the problem of optimization the process of bringing parameters of mass-inertia asymmetry of the conical flying model to specified standards is considered in the article. The only correction plane is designed to be positioned close to cone face, away from the center mass of the flying model. The flying model as a component of prefabricated rotor is being balanced in dynamic mode on a low-frequency dynamic vertical stand, which based on gas bearings. Before balancing experiment the weigh, longitudinal center of mass and inertia moments of the flying model have to be controlled with use of another measurement equipment.  As a criterion of optimization is sorted the reaching of minimum of the angle of deviation of principal longitudinal centroidal axis of inertia from geometrical axis of the flying model. But simultaneously the pre-set standard of center-mass shift from the geometrical axis must be ensured. Balancing algorithm, easy-to-realized by modern computers, is presented. Numerical illustration of balancing is given. The algorithm enables omitting intermediate steps of balancing, reducing them to one step (as a rule), and shortening the balancing time, as well. In one step of balancing the engineering model permits either bringing parameters of mass-inertia asymmetry of the flying model to specified standards, or diagnosing impossibility of attaining the specified standards with available design of flying model. The algorithm and balancing method are experimentally tested at newly-designed vertical dynamic stand on conical gas bearings. It’s high precision and efficiency are corroborated.

作者简介

Mariya Filonova

Tomsk State University of Control System and Radio Electronics

编辑信件的主要联系方式.
Email: cmm91@inbox.ru

Cand. Sc., senior Researcher, Department of Radio Engineering Systems

俄罗斯联邦, 40, Lenina Av., Tomsk, 634050

参考

  1. Klyuchnikov A. V. [Development and improvement of the algorithm single-plane balancing in a dynamic mode of high-speed flying models]. Vestnik SibGAU. 2015. Vol. 16, No. 2, P. 411–416 (In Russ.).
  2. Klyuchnikov A. V. [Numerical algorithm for the optimization of process trim tapered flying models on dynamic balancing stand]. Vestnik SibGAU. 2016, Vol. 17, No. 2, P. 309–317 (In Russ.).
  3. Glazyrina L. M., Karpovitskiy M. S., Klyuchnikov A. V., Malgin A. I., Smirnov G. G., Fomin Yu. P. Balansirovochnyy stend s vertikalnoy osyu vrashcheniya [Balancing stand with vertical axis of gyration]. Patent RF, no. 2292533, 2007.
  4. Glazyrina L. M., Karpovitskiy M. S., Klyuchni-kov A. V., Malgin A. I., Smirnov G. G., Fomin Yu. P. Sposob balansirovki rotora [Rotor’s counterbalancing method]. Patent RF, no. 2292534, 2007.
  5. Dmitriyevskii А. А., Lysenko L. N., Bogodistov S. S. Vneshnyaya ballistika [External ballistics]. Moscow, Mashinostroenie Publ., 1991, 640 p.
  6. Pravdin V. M., Shanin A. P. Ballistics of uncontrollable flying machines [Ballistika neupravlyaemih letatelnih apparatov]. Snezhinsk, RFNC-VNIITF Publ., 1999, 496 p.
  7. Klyuchnikov A. V. [The algorithm of single-plain dynamic balancing process of a conical flying prototype with optimization by criteria of achieve the minimum deviation of main centroidal axis of inertia]. Materialy XXIII Mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniia” [Proc. 23th Int. Technol. Conf. “Reshetnev reading”]. Krasnoyarsk, 2019, Part 1, P. 30–32 (In Russ.).
  8. Ilinykh V. V., Klyuchnikov A. V., Mihailov E. F., Timoshchenko A. G. [Technological support of quality during the manufacture of hypersonic uncontrollable flying models]. Vestnik SibGAU. 2013, Vol. 49, No. 3, P. 191–196 (In Russ.).
  9. Klyuchnikov A. V. [Method of eliminate a technological rig on measurement results during dynamic counterbalancing of flying vehicle]. Materialy XIX Mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniia” [Proc. 19th Int. Technol. Conf. “Reshetnev reading”]. Krasnoyarsk, 2015, Part 1, P. 21–23 (In Russ.).
  10. Abyshev N. A., Klyuchnikov A. V., Mikhailov E. F., Chertkov M. S. [Stand for precise non-contactable counterbalancing in dynamic regimen of conical rotors]. Trudy XIX Mezhdunarodnogo simpoziuma “Nadyozhnost i kachestvo” [Proc. 19th Int. Technol. Symp. “Reliability & Quality”]. Penza, 2014, Vol. 2, P. 234–236 (In Russ.).
  11. Klyuchnikov A. V. [Test equipment for diagnostics of a mass symmetry distribution of compound rotor’s detailes]. Trudy IX Mezhdunarodnoy nauchno-prakticheskoy konferentsii “Innovatsii na osnove informatsionnyh i kommunikatsionnyh tehnologiy” [Proc. 9th Int. Scientif. and Pract. Conf. “Innovations Based on Information and Communication Technologies”]. Moscow, 2012, Part 1, P. 21–23 (In Russ.).
  12. Klyuchnikov A. V. Sposob balansirovki rotora v odnoy ploskosti korrektsii [Method of rotor’s counterbalancing in singular place for correction]. Patent RF, no. 2499985, 2013.
  13. Klyuchnikov A. V. [Precised mathematical model for valuing of mass-inertia asymmetry parameters of a lengthened rotor]. Trudy XVII Mezhdunarodnogo simpoziuma “Nadyozhnost i kachestvo” [Proc. 17th Int. Technol. Symp. “Reliability & Quality”]. Penza, 2013, Vol. 1, P. 224–227 (In Russ.).
  14. Andreev S. V., Klyuchnikov A. V., Mihailov E. F. [Prospects of application of dynamic counterbalancing method for testing of flying machine’s mass-inertia asymmetry parameters]. Materialy XVIII Mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniia” [Proc. 18th Int. Technol. Conf. “Reshetnev reading”]. Krasnoyarsk, 2014, Part 1, P. 8–10 (In Russ.).
  15. Klyuchnikov A. V. Sposob nastroiki balansirovochnogo stenda dlya opredeleniya parametrov masso-inertsionnoy asimmetrii rotorov [Method of adjusting a counterbalance machine for determination of rotors’ mass-inertia parameters]. Patent RF, no. № 2453818, 2013.
  16. Klyuchnikov A. V. [Methodical ensuring a process of individual adjusting the dynamic balancing machine in the controlled object]. Trudy XIV Mezhdunarodnoy nauchno-prakticheskoy konferentsii “Innovatsii na osnove informatsionnyh i kommunikatsionnyh tehnologiy” [Proc. 14th Int. Scientif. and Pract. Conf. “Innovations Based on Information and Communication Technologies”]. Moscow, 2017, P. 382–386 (In Russ.).
  17. Andreev S. V., Klyuchnikov A. V., Lysykh A. V., Mikhailov E. F. [Calibrate operations during detail’s module counterbalancing on a non-adjusted dynamic counterbalance machine]. Trudy XVIII Mezhdunarodnogo simpoziuma “Nadyozhnost i kachestvo” [Proc. 18th Int. Technol. Symp. “Reliability & Quality”]. Penza, 2013, Vol. 2, P. 129–131 (In Russ.).
  18. Klyuchnikov A. V. Sposob balansirovki rotora v odnoy ploskosti korrektsii [Method of rotor’s counterbalancing in singular place for correction]. Patent RF, no. 2694142, 2019.

补充文件

附件文件
动作
1. JATS XML
下载

版权所有 © Filonova M.M., 2020

Creative Commons License
此作品已接受知识共享署名 4.0国际许可协议的许可
##common.cookie##