检索

期
标题
作者
卷 89, 编号 1 (2022)
Assessment of the compaction effect and operational characteristics of a crawler tractor based on a rheological approach
Nosov S., Рeregudov N.
PDF
(Rus)
卷 88, 编号 1 (2021)
Evaluation of methods for experimental and analytical determination of the contour area of the contact patch of a pneumatic tire with a support base
Lipkan' A., Panasyuk A., Godzhayev Z., Lavrov A., Rusanov A., Kazakova V.
PDF
(Rus) PDF
(Eng)
卷 88, 编号 2 (2021)
Comparative analysis of methods for improving the quality of hardened pipe and bar stock for agricultural machinery parts
Dement'yev V., Zasypkin A.
PDF
(Rus) PDF
(Eng)
卷 79, 编号 5 (2012)
General solution of the problem of shaft correcting optimization during the agricultural machines' repair
Manilo I.
卷 83, 编号 11 (2016)
Determination of stiffness parameters of toothed gears of automobiles and tractors
Tarasik V.
PDF
(Rus)
卷 82, 编号 1 (2015)
Device for investigation of seeds of oil crops under compression
Shevchuk R., Shevchuk V.
卷 79, 编号 3 (2012)
Introduction in the theory of involvement of soil masses in movement with specific reference to the soil processing
Imamov I., Belov S., Vorobiov Y.
卷 82, 编号 9 (2015)
Increasing soil compacting impact by roller of a combined machine for preplanting cultivation
Akhmetov A.
卷 90, 编号 1 (2023)
Calculation of normal stiffness and contact patch of ultra-low pressure tires for agricultural machinery
Balakina E., Godzhaev Z., Konshin A., Kochetov M.
PDF
(Rus)
卷 77, 编号 9 (2010)
Introduction in the theory of involving of soil masses in movement on an example of soil processing
Imamov I.
卷 87, 编号 3 (2020)
Computational and experimental assessment of the influence of ultra-low pressure tires of mobile power equipment on soil
Godzhaev Z., Goncharenko S., Artemov A., Pryadkin V., Godzhaev T.
PDF
(Rus)
卷 79, 编号 10 (2012)
Analysis of belts deformation by pulleys in flax harvesting machines
Kovaliov M., Vinogradov A.
卷 77, 编号 5 (2010)
An analysis of energy consumption for the displacement of soil in vertical plane with a mouldboard during the ploughing
Nikolayev V., Yurkov M.
卷 84, 编号 5 (2017)
Forecasting the durability of hollow shafts and axles of agricultural machinery products
Dement'ev V., Zasypkin A.
PDF
(Rus)
卷 79, 编号 10 (2012)
An energy-saving modular tiller
Rudenko N., Lyakhov A., Gerasimov Y., Padaltsin K.
卷 77, 编号 4 (2010)
Deformation of soil with double-mouldboard plough during the broadcast seeding in the irrigated crop farming
Saakyan S.
卷 84, 编号 5 (2017)
The method of constructing the diagrams of tangential stresses in the contact zone of an axle wheel with soil
Godzhaev Z., Rusanov A., Revenko V.
PDF
(Rus)
卷 81, 编号 10 (2014)
Effective design of protection module for passive safety of cabs
Karapetyan M., Orlov N., Kuzmin D.
卷 88, 编号 3 (2021)
Installation of screw reduction UVO 20-50 for hardening and calibration of cylindrical parts and billets of agricultural machinery
Dement'yev V., Zasypkin A., Sterkhov M., Churkin A.
PDF
(Rus)
卷 77, 编号 4 (2010)
Energy consumption for the soil layer turning
Nikolayev V.
卷 79, 编号 9 (2012)
Forecasting of service life of knots of repair and technological equipment in the enterprises of agrarian and industrial complex
Komarov V., Lezin P., Grigoryev A.
卷 77, 编号 2 (2010)
Improving bearing assembly of turbo-supercharger for motor-and-tractor internal combustion engine
Makushin A., Kulakov A., Gaffarov A.
卷 83, 编号 1 (2016)
Research of movement of hexagonal and circular disk working organs of tillage machines
Kobyakov I., Yevchenko A.
PDF
(Rus)
卷 76, 编号 11 (2009)
Air-cooled diesel's cylinder deformation
Belov Y., Gots A.
卷 82, 编号 12 (2015)
Determination of optimality criteria in the development of hardening technologies
Dementyev V., Zasypkin A.
卷 79, 编号 4 (2012)
Hardening of track's pins of tracked machines with screw compression during the high-temperature thermomechanical processing
Zasypkin A., Dementyev V.
卷 86, 编号 6 (2019)
Development of a method for obtaining a section of reduced stiffness on the elastic characteristic of a vehicle tire
Ryabov I., Pozdeev A., Erontaev V., ZHdamirova E.
PDF
(Rus)
卷 82, 编号 11 (2015)
System analysis of process of high-temperature thermomechanical treatment for blanks of hollow track pins
Dementyev V., Zasypkin A.
1 - 28 的 28 信息

检索提示:

  • 检索的名词区分大小写
  • 常用字词将被忽略
  • 默认情况下只有在查询结果满足所有检索词才返回（例如，隐含AND）
  • 使用OR结合多个检索词，便于查找含有这些检索词的文章，例如education OR research
  • 使用括号来创建更复杂的查询; 例如：archive ((journal OR conference) NOT theses)
  • 使用引号检索一个完整的词组; 例如： "open access publishing"
  • 使用-或者NOT排除一个检索词; 例如：online -politics or online NOT politics
  • 在检索词里使用 *作为通配符匹配任何字符序列; 例如., soci* morality 将符合含有 "sociological" or "societal"的词语

##common.cookie##