Vol 3, No 1 (2009)


Molecular Energy Storage Application in the Starting System of URAL-432031 Truck

Antipenko V.S., Lebedev S.A.


The work examines starting devices for an internal combustion engine of the automobile URAL-432031, their structure and characteristics of their component, results of the tests conducted in the Ryazan military automobile institute.
Izvestiya MGTU MAMI. 2009;3(1):8-12
pages 8-12 views

Oscillations of a Rotor of the Valve Traction Motor

Berbirenkov I.A.


The article considers the structure of the valve traction motor with synchronous electromechanical transformer. Oscillations of the rotor of the synchronous motor may be caused by various reasons, e.g.: cyclic work of a traction inverter, pulsation of conductivity of operating air clearance, natural and forced oscillations of the rotor.
Izvestiya MGTU MAMI. 2009;3(1):12-14
pages 12-14 views

Noise Reduction for Exhaust of the Piston Internal-combustion Engine with Coaxial Gas Outflow

Vakhitov Y.R., Enikeev R.D.


The article deals with the results of the numerical research of the engine exhaust noise reduction by means of coaxial arrangement of muffler exhaust pipes. This method provides significant exhaust noise reduction. The optimal ratios of pipe cross sections are determined.
Izvestiya MGTU MAMI. 2009;3(1):14-17
pages 14-17 views

Analysis of the Effect of Restricted Stress-strain Adhesive Joint and Its Application in Bus Industry

Voronkov O.V., Peskov V.I.


The article describes an effect which takes place in case of adhesive joint of two parts when elasticity modulus of these parts is much bigger than elasticity modulus of glue. The main point of the effect can be described as huge increase of glue layer compression-tension stiffness caused by conditions of glue material called tight stress-strain.
Izvestiya MGTU MAMI. 2009;3(1):17-24
pages 17-24 views

Kolebaniya rulevogo upravleniya avtomobilya

Emelyanov S.R.


The article is about study of influence of steerable wheels disbalance and manufacturing inaccuracy of brake disks on and local vibration. There is the method of dynamic absorbing of resonance oscillations. The author suggests a principle design of a dynamic absorber of oscillations.
Izvestiya MGTU MAMI. 2009;3(1):24-27
pages 24-27 views

Body Design of a Tracked Carrier

Ershov M.Y., Lepeshkin I.A.


This paper describes the design of the light-class all terrain tracked carrier's body, developed by order given by STC Spectehnika MAMI. This design meets the modern technical requirements as well as terms of esthetics and ergonomics.
Izvestiya MGTU MAMI. 2009;3(1):27-34
pages 27-34 views

Modern Antilock Brake Systems and Realization of Their Operation Algorithms

Klimenko V.I., Ryzhikh L.A., Krasyuk A.N., Leontyev D.N.


This paper deals with principles of realisation of algorithms of antilock brake system (ABS) in modern vehicles and their further developement.
Izvestiya MGTU MAMI. 2009;3(1):34-37
pages 34-37 views

Relation between Tire Rate Value and Vehicle Operation Performance

Kondrashov V.N., Voronin V.V., Karpukhin K.E.


The paper deals with the analysis of characteristics of rigidity of the tyre, such as: normal rigidity; lateral rigidity; longitudinal rigidity; angular rigidity; torsional rigidity. Influences of the above-stated characteristics on operational performance of vehicles are considered. The authors give recommendations of designing of new tyres taking into account their subsequent application on modern cars.
Izvestiya MGTU MAMI. 2009;3(1):37-40
pages 37-40 views

Clutch Load Determination on the Basis of Test Data

Kretov A.V., Esakov A.E.


This article considers the method of experimental estimation of automotive friction clutch slipping work and power. The authors give the theoretical basis of the proposing method and estimate its precision. In this case the research time and expenses are reduced and decreasing of explored processes precision should not exceed 10 % which is acceptable for many engineering investigations.
Izvestiya MGTU MAMI. 2009;3(1):41-46
pages 41-46 views

Accuracy Enhancement for Vehicle Motion Mathematical Model on the Basis of Test Results

Kurmaev R.K., Lepeshkin A.V.


The article gives comparison of test results of all-wheel drive vehicle Gidrokhod-49061 equipped with hydrostatic transmission with the results of mathematical simulation under similar road conditions. By this comparison the mathematical model was corrected. Finally the adjusted mathematical model of motion is adequate to test results.
Izvestiya MGTU MAMI. 2009;3(1):46-56
pages 46-56 views

Mathematical Model of the Tire Cornering Coefficient for Wheeled Vehicles

Mikhailin I.A.


This article presents a mathematical model of tire cornering coefficient for wheeled vehicles and suggests a method of the coefficient calculation
Izvestiya MGTU MAMI. 2009;3(1):56-60
pages 56-60 views

Automatic Control of Hybrid Transmission of an All-Wheel Drive Vehicle

Prediger V., Hoffmann J., Trentmann V., Kostilev S., Lohmann E., Selifonov V.V., Karpukhin K.E., Baulina E.E.


The present article describes the bases of automatic control by an internal combustion engine and reversible hybrid drive under work in mode of traction electric motor and generator of the all-wheel drive, multi-purpose car with parallel hybrid drive on an example of a UAZ 3153 car equipped with hybrid power instalation.
Izvestiya MGTU MAMI. 2009;3(1):60-67
pages 60-67 views

Approximation of Engine Part-load Curves

Solomatin N.S., Zamorin A.G., Zotov E.M.


The paper examines the problem of mathematic description of partial characteristics of the internal combustion engine. It is the most advisable to describe the experimental speed performance of engine by means of the multidimensional spline approximation. This method provides creating the surface which copies the experimental speed performance with rather range of accuracy.
Izvestiya MGTU MAMI. 2009;3(1):68-71
pages 68-71 views

Dependence of Vehicle Stopping Distance on Driver's Psychophysiologic Condition

Tarabkin V.S., Akimov A.V.


Commercial vehicles play an essential role of physical distribution, working as indispensable means of transportation and play as our dependable partner in our social life. On the other hand, problems of traffic accidents are key issues which we must solve more urgently. Driver condition monitoring systems are the basic branch of transportation safety field.
Izvestiya MGTU MAMI. 2009;3(1):71-73
pages 71-73 views

Application of Material Structuring Methods for Improvement of Vibroacoustic Properties of Panels, Laminated Gaskets in Passenger Cars

Fesina M.I., Krasnov A.V.


Results of experimental researches structured noisereduced materials and the details that have been lead with use of specialized laboratory - bench installations (Cabin Alpha, Tower Pisa, RTC-3, Oberst) are submitted. Illustrative examples of constructive - technological structurization of details (linings, panels and upholsteries), providing decrease in noise of vehicle are resulted. Results of the researches lead by authors testify to essential reserve increase in acoustic efficiency noisereduced materials and details.
Izvestiya MGTU MAMI. 2009;3(1):73-85
pages 73-85 views

Selection of Method for Electronic Gear Control

Shipilevsky G.B., Gorbachev A.S.


The article examines solution of the task of gear control in tractor transmissions. There are three main layouts of friction clutch installation within tractor transmission. For each one the mathematical formulation is given. The authors suggest possible criteria for selection of gear control method under load.
Izvestiya MGTU MAMI. 2009;3(1):85-90
pages 85-90 views

Optimization of Transmission Control Laws for All-wheel Drive Vehicles with Individual Drive Per Wheel

Bakhmutov S.V., Gusakov D.N.


The article considers results of analytical study on optimization of power distribution in multiaxis all-wheel drive vehicles. On the basis of multicriterion optimization methods the authors conducted the research influence of interaxial and cross-axle power distribution on vehicle controllability, stability and fuel efficiency.
Izvestiya MGTU MAMI. 2009;3(1):90-98
pages 90-98 views

Dimensioning in Combined Cutting-deforming Machining with Axial Oscillations

Ankin A.V., Adeev A.S.


The paper examines dimension processing in the technological system for combined cutting-deforming machining of needle shafts class. Actually dimension processing provided by cutting block, while the rollers of deforming part forming of surface roughness with plastic deformation method. Detail the process of the axial oscillation for removal of elastic-reduced metal after cutting. The mathematical model for calculating the error of machining consists of two parts. Computer modeling and subsequent analysis of the solutions will help to design technological process of combined cutting-deforming machining of needle shafts class and assign these modes of machining, which will provide the quality of demanded parameters: the dimension of part and surface roughness.
Izvestiya MGTU MAMI. 2009;3(1):99-102
pages 99-102 views

Electron Work Function of Refractory Metal Alloys

Arzamasov V.B., Smirnova E.E., Stroev A.A., Polunov I.L., Rykov D.E.


The article considers experimental investigation of influence of tungsten alloying by transitive metals of IV A - VI A groups on its thermoemission properties. It is established that at temperatures of test 1500 and 2400 С almost monotonous reduction of electron work function of pure tungsten is observed after additing of the given alloying elements. It is shown that at a certain temperature on surface of the sample the layer of atoms of zirconium adsorbed from internal volumes is formed that essentially increases alloy thermoemission.
Izvestiya MGTU MAMI. 2009;3(1):102-104
pages 102-104 views

Mathematical Model of Physical Processes in Vibration-laden Screw-thread Joint

Berezin S.Y., Leonov V.N.


The theoretical questions of stability of screw-thread connection are considered on the basis of mathematical model, representing physical processes under vibration.
Izvestiya MGTU MAMI. 2009;3(1):105-109
pages 105-109 views

Manufacturing of Round and Square Hot-rolled Bars of Nickel and Titanic Alloy on the Rolling Mill 280 - 380

Burlakov I.A.


The rolling process of titanium and nickel alloy-based round and hexagonal rods using the «280-380» mill is considered. The technical specification of the rolling mill and straitening machine is given. The paper considers power data calculation which is important for forming tool correction. The above mentioned equipment makes possible to roll the rods of required shape and provide high mechanical properties of rolled materials.
Izvestiya MGTU MAMI. 2009;3(1):109-111
pages 109-111 views

Cutting Method for Roll Material Decks by High-pressure Water-ice Flow

Burnashov M.A.


The article describes a new cutting method for decks of rolled materials with application of high pressure water-ice flow as a cutting tool. The authors consider the equipment, the water-ice tool and means of technological equipment used during carrying out of experimental researches.
Izvestiya MGTU MAMI. 2009;3(1):111-114
pages 111-114 views

Determination of Optical Centers of Emission in a Plastic Scintillator Irradiated by UV-laser

Volkova L.V., Borisova E.A., Nurmukhametov R.N.


Photoprocesses in a plastic scintillator irradiated by UV-laser were studied. The spectral properties and structure of photoproducts in irradiated plastic scintillator were found. The mechanism of photochemical processes leading to radioluminescence signal decrease in the scintillator during its usage has been suggested
Izvestiya MGTU MAMI. 2009;3(1):114-118
pages 114-118 views

Improvement of Labor Protection in the Scientific-Production Association of Measurement Technique

Grafkina M.V., Angelova M.V.


In current economic conditions manufacturers of electronics, measurement, and radio engineering intend to improve quality and competitiveness of their products, so they develop, implement and certify quality management system. The authors propose improvement of safety in these enterprises by integrating aspects of safety into the quality management system.
Izvestiya MGTU MAMI. 2009;3(1):118-121
pages 118-121 views

Monitoring of Microarc Oxidation Process with Application of personal computer

Zhukovsky A.V., Shandrov B.V.


The article considers monitoring of the microarc oxidation process via PC. A series of computer programs is developed. The obtained results allow to assess the sustainability of the process in various modes and at different stages of the process of oxidation and to determine the time of transition to a dangerous regime.
Izvestiya MGTU MAMI. 2009;3(1):121-123
pages 121-123 views

Vibration of the Cross-section of a Nonrigid Hollow Cylinder Unit under Combined Treatment by Cutting and Surface Plastic Deformation

Maximov Y.V., Ankin A.V., Vetrova E.A.


The process of combined machining by cutting and surface plastic deformation of nonrigid smooth hollow cylinder parts leads to creation of radial, bending and complex twisting oscillations of cross-sectional view of the part blank. These oscillations have an effect on dimension parameters of the combined machining of parts.
Izvestiya MGTU MAMI. 2009;3(1):124-127
pages 124-127 views

Determination Peculiarities of Static and Ddynamic Quality Index of Basic Parts

Mihaylov V.A., Porhunov S.G.


In modern machine-tool industry welded base constructions are rather widely used. The calculation is realized, as a rule, without the consideration of weld joints and the change of material properties in heat-affected area. In this project the task of development and check of effective simulation of base details on the basis of Finite elements method is solved.
Izvestiya MGTU MAMI. 2009;3(1):127-134
pages 127-134 views

Statistical Analysis of Accuracy for Electrochemical Working of a Compressor Blade

Morgunov Y.A., Benikov V.S., Saushkin S.B., Saushkin G.B.


The article is about statistical investigation of accuracy achieved with electrochemical machining of gas turbine engine compressor blades. On the base of received data the authors propose improvement the output technical characteristics of ECM operation. It is shown that dimensional accuracy approximately 0.1 mm and surface efficiency nearby Ra = 1,6 mcm are reliably realized during ECM.
Izvestiya MGTU MAMI. 2009;3(1):134-138
pages 134-138 views

Organization of On-line Information Analysis in the System of Decision Making by Results of Factory Testing of Products

Pervukhina E.L., Golikova V.V., Stepanchenko T.L.


The article is about peculiarities and principle of operative information analysis in the system of decision making support for industrial testing of devices are considered. The main goal of the device assessment is to select devices capable of utilization. The information analysis orientates on detection and consequent tracking of the joint tendency of device parameter changing. The vector autoregression which connects current and past values of parameters is used to model the devices during their industrial testing.
Izvestiya MGTU MAMI. 2009;3(1):138-144
pages 138-144 views

Innovative research and development based on of 3D parametric modeling technology

Shpun'kin N.F., Petrov P.A., Strokov P.I., Gnevashev D.A., Nikitin M.Y.


The paper presents the results of innovative research and development based on of 3D parametric modeling technology. Due to the time-saving for R&D, the use of three-dimensional models makes it possible to hasten the preproduction process and to increase the competitive ability of new products. Some examples of the developed projects are presented.
Izvestiya MGTU MAMI. 2009;3(1):144-147
pages 144-147 views

Manufacturing Capabilities of Brushes with Abrasive Polymeric Fibres

Pini B.E., Yakovlev D.R.


Abrasive-polymeric brushes have been known since 80s. They were successfully applied at internal surface machining for deflashing of leading edges in hydraulic distributor bores. Authors conducted operation of deflashing on milled crown of caps by means of brushes with abrasive polymeric fibres. Selected operation modes ensured high quality and reduced time of treatment.
Izvestiya MGTU MAMI. 2009;3(1):148-151
pages 148-151 views

Principles of Extruding Forging Die Design

Ragulin A.V., Anukhin A.S., Filippov Y.K., Kononov A.V.


This paper is about die design principles according to technical, social and economic demands by example of development of cold forging procedure ball pin body. Authors analyzed metal flow kinematics under product shaping on forging transitions with computer modeling. There are local effects going with forming process, including distribution and changing of specific forces on die walls and punch and pusher faces.
Izvestiya MGTU MAMI. 2009;3(1):151-156
pages 151-156 views

Efficiency of Risk Reducing Measures (ferric impurity removal) for Safety Operation. Residual Risk.

Sandulyak A.A.


There were introduced and analyzed such concepts as reduction of risk (including relative risk), and residual risk, that depends on removal from working medium ferroimpurities. There were found functional relatives with argument as efficiency of ferroimpurities removal and residual fraction of ferroimpurities in the working medium.
Izvestiya MGTU MAMI. 2009;3(1):156-160
pages 156-160 views

Ways of Energy Intensity Reducing for Hydrocutting of Sheet And Roll Nonmetallic Material

Stepanischev M.A., Burnashov M.A.


The article is about the analysis of modern ways of cutting of nonmetallic materials with application of energy of high-speed liquid streams with instructions of their merits and demerits. New ways of cutting of sheet and rolled materials, based on application of energy of high-speed liquid streams allow to lower power consumption of existing processes considerably.
Izvestiya MGTU MAMI. 2009;3(1):160-165
pages 160-165 views

Application of Probabilistic Approach to Describe the Kinetic Curves of Dissolution And Leaching of Magnetite

Artamonova I.V., Gorichev I.G., Izotov A.D., Pichugina N.M., Stepanov V.M.


Proposed kinetic analysis of the processes of dissolution is based on use of principles of synergetics, fractal geometry, heterogeneous kinetics, using probabilistic approaches to the description of the interaction of oxide with a solution. The authors investigated in details the mechanisms of dissolution of magnetite and other oxides of iron in sour environments with the purpose to determine the mathematical equations that describe the kinetic curves of dissolution and leaching of magnetite.
Izvestiya MGTU MAMI. 2009;3(1):166-173
pages 166-173 views

Basic Regularities of Electrochemical Behavior of Steel 10 in the Anodic Polarization in Sulfate And Carbonate Solutions at Different Ph Environments

Artamonova I.V., Balashova O.P., Bratishko R.K., Zabenkina E.O., Lesnova L.A., Rusakova S.M.


The effect of carbonate ions for the type of polarization curves under anode polarization in carbonaceous solutions under different pH environments is investigated. The existence of two peaks on the curves of current-potential is shown. The substantiation of influence of carbonate ions on the anodic process is given. The mathematical model of dissolution of iron in carbonaceous solutions is offered .The mechanism of the description of polarizing curves of dissolution of iron in neutral and alkaline conditions is given.
Izvestiya MGTU MAMI. 2009;3(1):173-179
pages 173-179 views

The Computerized Means for the Automation of Qualifying Operations Based on Labview Technology

Sirotsky A.A., Murachev E.G., Dorokhov I.N.


The problems of the high-precision and automated control are actual for all branches of modern mechanical engineering. Modern trends dictate necessity to create the highly effective computerized information-measuring systems. One of the most effective means of establishing computerized systems of gathering and data processing is the software LabVIEW. The program of gathering and data processing from laser measuring system (LMS) with module application of data gathering PCI-1202H created by ICP DAS is described in Lab VIEW.There are modules of the program, created in the graphical programming language G (J). The methods of programming of computerized measuring systems are described. The results of experimental studies of created LMS with the computerized system of gathering and data processing are shown.
Izvestiya MGTU MAMI. 2009;3(1):179-185
pages 179-185 views

The Films with Low Dielectric Permittivity on the Basis of Lyotropic Liquid Crystals

Sonin A.A.


The possibility of preparation of solid porous films with low dielectric constant for use in nanoelectronics was demonstrated on example of the CTAB/TEOS/NaSal and CTAB/TEOS/TCS-2 novel precursor solutions. The dielectric constant and mechanical modules of these films were measured. The possibility of use of supercritical CO2 for improvement of the film characteristics was shown.
Izvestiya MGTU MAMI. 2009;3(1):185-192
pages 185-192 views

Role Play As a Means of Shaping the Social And Cultural Competence of Students-Economists in the Technical University

Bagramyants M.L., Bagramyants N.L.


This paper describes the theoretical and practical components of formation of cross-cultural competence for students-economists by using a role-playing game. There are conditions that ensure the maximum efficiency of this kind of student's speech activity. Analysis of the procedural part of the linguistic interactions in role-playing games are provided. The characteristic of language material taking into account features of foreign language teaching in the conditions of technical university is given.
Izvestiya MGTU MAMI. 2009;3(1):193-196
pages 193-196 views

Possible Risks in the Implementation of Major International Projects (by Example of the Black Sea Ring Road)

Volkova Y.A., Popova M.A., Yakovenko A.G.


In this paper the authors attempt to analyze the three main types of risks: financial and macroeconomic, geopolitical, and international, as well as technological and environmental. At the same time, the authors make the market optimistic that the creation of a modern transport infrastructure is so urgent problem that the Black Sea state, in any case be forced to take its decision within their territories, even without linking it with the unified plan.
Izvestiya MGTU MAMI. 2009;3(1):196-200
pages 196-200 views

Directions of Activization of Universities in the Process of Building a Sustainable Competitiveness

Kravtsova V.I.


The questions focused on optimum use of innovative potential at integration processes of universities with manufacture and research organizations. Proposed to strengthen the role of Academic Boards and Councils for the Protection of doctoral and master's theses in the field of scientific expertise and innovative management functions, as well as advance training. Attention focuses on the distribution of system of confidential management in institutions and formation of the management of innovation development.
Izvestiya MGTU MAMI. 2009;3(1):200-205
pages 200-205 views

Controllability and Stability in Macroeconomic System

Katanaev N.T., Arkatova N.A., Bаsanets P.P.


The problem of stability and controllability of economic facilities in industrial cycle development are investigated. The authors made estimation of vehicle manufacture growth dynamics in various phases of development of an industrial cycle. The reasons of unsustainable development processes in the economy are revealed.
Izvestiya MGTU MAMI. 2009;3(1):206-210
pages 206-210 views

Practical Realisation of the Innovative Approach to Foreign Language Training in Non-linguistic Universities

Aslamova T.V., Bashmakova I.S.


It is obvious that during the intensive process of informatization of education, new approaches, methods, new teaching materials are developed. The objective of this article focus on such methods as training in collaboration, project method, learning problems, notably : discussion, role-play problem orientation, etc. Because they're the most effective methods for the formation of linguistic and communicative competence of students at not language universities on material of socio-technical issues of the Internet, which is a priority today.
Izvestiya MGTU MAMI. 2009;3(1):210-215
pages 210-215 views

Estimation of Real Cost of Assets as the Factor of Anticipatory Management Today

Markov V.V.


The article discusses issues related to the valuation of the assets of the company, shows the significance of the degree of objectivity of such assessment for the country's economy and anticipating crisis situations. The valuation of assets, used by Russian companies are studied. Methods to improve the objectivity of this evaluation to improve management are proposed.
Izvestiya MGTU MAMI. 2009;3(1):215-220
pages 215-220 views

Objective Necessity of State Regulation of National Economy

Raikova L.I.


The necessity for a modern market economy to use government regulation of national economy are revealed. Especially, the necessity increases with the development of crisis situations in the national economy.
Izvestiya MGTU MAMI. 2009;3(1):220-223
pages 220-223 views

The Formalization of Evaluation Indicators of Long-Term Forecasting Conditions of Trucks Russian Market

Nevelev V.A., Gontar M.M.


The authors propose a formalization of the measurement of indicators of long-term prediction market of the trucks Russian market which based on market research. It's provide the use of modifications of inter-sectoral balance model, a multifactor regression model, the model flexibility and data-processing model.
Izvestiya MGTU MAMI. 2009;3(1):223-228
pages 223-228 views

Economic Background for Making Hybrid Vehicles

Rozhnova O.V., Karpukhin K.E., Frolova E.S.


This paper deals with economic preconditions of creation of cars with a hybrid power installation. The results of the tests confirming decrease of the expense of fuel and toxicity of fulfilled gases of experimental car MAMI with a hybrid power installation on fuel profitability and toxicity of fulfilled gases are resulted.
Izvestiya MGTU MAMI. 2009;3(1):228-230
pages 228-230 views

History of punctuation marks

Anokhina T.Y.


The paper deals with the history of punctuation marks in Russian. The hindsight to the emergence of punctuation marks is given. The paper reveals the basic principles of contemporary Russian punctuation.
Izvestiya MGTU MAMI. 2009;3(1):230-233
pages 230-233 views

Some Problems of Higher Education in the Modern World

Gadelshin T.K.


The article analyses the level of mathematical preparation of graduates from the Russian schools. Problems of students' adaptation to the university education are considered. Problems of the transition to the two-level system of professional training are discussed.
Izvestiya MGTU MAMI. 2009;3(1):234-238
pages 234-238 views

Preparation of a Modern Specialist in Higher Vocational Education

Eremeeva L.V.


The connection between the economic and cultural state of the society and the educational system is analyzed in the article. The question of professionally competent engineering staff in the context of the requirements of the modern society are discussed and suggests the ways to resolve it.
Izvestiya MGTU MAMI. 2009;3(1):238-242
pages 238-242 views

Prospects And Possible Trends in Development of Highest Professional Education

Zubkov V.G., Koltunov I.I., Akimov A.V.


In the article questions of prospects and possible trends in development of domestic highest professional education are discussed. The wide use of modern information and distant technologies in the educational process is proposed.
Izvestiya MGTU MAMI. 2009;3(1):242-249
pages 242-249 views

Modern Technologies for Training of Engineers at the Technology of Mechanical Engineering Department

Shandrov B.V., Balashov V.N.


The article considers problems of preparation of engineers at the training final stage. The issues of lecture's material presentation and the degree of graduate work are stated.
Izvestiya MGTU MAMI. 2009;3(1):249-252
pages 249-252 views

Innovative Technology and Training Teachers for Secondary Education

Kharitonov V.I.


This article discusses the possibility of combining traditional and modern information technologies in educational process. A program of the course «Modern technologies of training» for the professional development of teachers is offered. Necessity of introduction on faculty of improvement of professional skill teachers of a rate "Information networks and telecommunications" is proved.
Izvestiya MGTU MAMI. 2009;3(1):252-256
pages 252-256 views

Substantiation for the Innovative Training for Industrial Enterprises Specialist

Svetlov I.E.


The article shows the need for the development of enterprises based on innovation introduction. The aggravation of a personnel situation in the industry of the Russian Federation is noted. It's considering the problem of interaction between enterprises and universities and suggests some solutions by means of creation the corporate education space.
Izvestiya MGTU MAMI. 2009;3(1):256-262
pages 256-262 views

Educational-methodical Work Improvment

Petrov M.S.


The questions of the organization of the educational process of improving teaching work at the present reform of higher education are considered.
Izvestiya MGTU MAMI. 2009;3(1):262-264
pages 262-264 views

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies